Jason Rumney
README.md
Device Configuration Files
This directory contains device configuration files, describing the workings of supported devices. The files are in YAML format, and describe the mapping of Tuya DPs (Data Points) to HomeAssistant attributes.
Each Tuya device may correspond to one primary entity and any number of secondary entities in Home Assistant.
The Top Level
The top level of the device configuration defines the following:
name
The device should be named descriptively with a name the user would recognize, the brand and model of the device is a good choice. If a whole family of devices is supported, a generalization of the model type can be used. The name should also indicate to the user what type of device it is.
products
Optional, for future use.
A list of products that this config applies to. Each product in the list must
have an id specified, which corresponds to the productId or productKey
(depending on where you are getting it from) in Tuya info. This is available
from the Tuya developer web portal listing for your device, or when using
UDP discovery (via tinytuya). In future it is intended that UDP discovery
will be used to more precisely match devices to configs, so it is recommended
to report these if you can find them when requesting a new device. Each
listing can also have an optional name, which is intended to override the
top level name when full support for this field is added.
Probably other info will be added in future to provide better reporting of
device manufacturer and model etc.
primary_entity
This contains the configuration for one Home Assistant entity which is considered the main entity for the device. For example, if the device is a heater, this would be a climate entity.
The configuration for entities is detailed in its own section below.
secondary_entities
Optional.
This contains a list of additional Home Assistant entities providing additional functionality beyond the capabilities of the primary entity. Examples include lighting control for display panels as a Home Assistant light entity, child locks as a Home Assistant lock entity, or additional toggles as Home Assistant switch entities.
The configuration for secondary entities is the same as primary entities, and is detailed in the section below.
Entity configuration
entity
The Home Assistant entity type being configured. Currently supported types are climate, switch, light, lock. Functionality for these entities is limited to that which has been required for the devices until now and may need to be extended for new devices. In particular, the light and lock entities have only been used for simple secondary entities, so only basic functionality is implemented.
class
Optional.
For some entity types, a device class can be set, for example switch
entities can have a class of outlet. This may slightly alter the UI
behaviour.
For most entities, it will alter the default icon, and for binary sensors
also the state that off and on values translate to in the UI.
category
Optional.
This specifies the entity category of the entity. Entities can be categorized
as config or diagnostic to restrict where they appear automatically in
Home Assistant.
dps
This is a list of the definitions for the Tuya DPs associated with attributes of this entity. There should be one list entry for each supported DPs reported by the device.
The configuration of DPs entries is detailed in its own section below.
name
Optional.
The name associated with this entity can be set here. If no name is set, it will inherit the name at the top level. This is mostly useful for overriding the name of secondary entities to give more information about the purpose of the entity, as the generic type with the top level name may not be sufficient to describe the function.
mode
Optional. For number entities, default="auto", for others, None
For number entities, this can be used to force slider or box as the
input method. The default auto uses a slider if the range is small enough,
or a box otherwise.
DPs configuration
id
Every DP must have a numeric ID matching the DP ID in the Tuya protocol.
type
The type of data returned by the Tuya API. Can be one of the following:
- string can contain arbitrary text.
- boolean can contain the values True or False.
- integer can contain only numbers. Integers can have range set on them, be scaled and steped
- bitfield is a special case of integer, where the bits that make up the value each has individal meaning.
- base64 is a special case of string, where binary data is base64 encoded. Platforms that use this type will need special handling to make sense of the data.
- hex is a special case of string, where binary data is hex encoded. Platforms that use this type will need special handling to make sense of the data.
- json is a special case of string, where multiple data points are encoded in json format in the string. Platforms that use this type will need special handling to make sense of the data.
- float can contain floating point numbers. No known devices use this, but it is supported if needed.
name
The name given to the attribute in Home Assistant. Certain names are used by the Home Assistant entities for specific purposes. If a name is not recognized as a standard attribute by the entitiy implementation, the attribute will be returned as a readonly custom attribute on the entity. If you need non-standard attributes to be able to be set, you will need to use a secondary entity for that.
readonly
Optional, default false.
A boolean setting to mark attributes as readonly. If not specified, the
default is false. If set to true, the attributes will be reported
to Home Assistant, but no functionality for setting them will be exposed.
optional
Optional, default false.
A boolean setting to mark attributes as optional. This allows a device to be matched even if it is not sending the dp at the time when adding a new device. It can also be used to match a range of devices that have variations in the extra attributes that are sent.
mapping
Optional. This can be used to define a list of additional rules that modify the DP to Home Assistant attribute mapping to something other than a one to one copy.
The rules can range from simple value substitution to complex relationships involving other attributes. It can also be used to change the icon of the entity based on the attribute value. Mapping rules are defined in their own section below.
hidden
Optional, default false.
This can be used to define DPs that do not directly expose Home Assistant
attributes. When set to true, no attribute will be sent. A name should
still be specified and the attribute can be referenced as a constraint
from mapping rules on other attributes to implement complex mappings.
An example of use is a climate device, where the Tuya device keeps separate
temperature settings for different Normal and Eco preset modes. The Normal
temperature setting is exposed through the standard temperature
Home Assistant attribute on the climate device, but the eco_temperature
setting on a different DP is set to hidden. Mapping Rules are used on the
temperature attribute to redirect to eco_temperature when preset_mode
is set to Eco.
range
Optional, may be required in some contexts, may have defaults in others.
For integer attributes that are not readonly, a range can be set with min
and max values that will limit the values that the user can enter in the
Home Assistant UI. This can also be set in a mapping or conditions block.
unit
Optional, default="C" for temperature dps on climate devices.
For temperature dps, some devices will use Fahrenhiet. This needs to be
indicated back to HomeAssistant by defining unit as "F". For sensor
entities, see the HomeAssistant developer documentation for the full list
of possible units (C and F are automatically translated to their Unicode
equivalents, other units are currently ASCII so can be easily entered directly).
class
Optional.
For sensors, this sets the state class of the sensor (measurement, total or total_increasing)
format
Optional.
For base64 and hex types, this specifies how to decode the binary data (after hex or base64 decoding).
This is a container field, the contents of which should be a list consisting of name, bytes and range fields. range is as described above. bytes is the number of bytes for the field, which can be 1, 2, or 4. name is a name for the field, which will have special handling depending on
the device type.
Mapping Rules
Mapping rules can change the behavior of attributes beyond simple copying of DP values to attribute values. Rules can be defined without a dps_val to apply to all values, or a list of rules that apply to particular dp values can be defined to change only particular cases. Rules can even depend on the values of other elements.
dps_val
Optional, if not provided, the rule is a default that will apply to all values not covered by their own dps_val rule.
dps_val defines the DP value that each
rule in the list applies to. This can be used to map specific values from the
Tuya protocol into attribute values that have specific meaning in Home
Assistant. For example, climate entities in Home Assistant define modes
"off", "heat", "cool", "heat_cool", "auto" and "dry". But in the Tuya protocol,
a simple heater just has a boolean off/on switch. It can also be used to
change the icon when a specific mode is operational. For example if
a heater device has a fan-only mode, you could change the icon to "mdi:fan"
instead of "mdi:radiator" when in that mode.
value
Optional.
This can be used to set the attribute value seen by Home Assistant to something
different than the DP value from the Tuya protocol. Normally it will be used
with dps_val to map from one value to another. It could also be used at top
level to override all values, but I can't imagine a useful purpose for that.
scale
Optional, default=1.
This can be used in an integer dp mapping to scale the values. For example
some climate devices represent the temperature as an integer in tenths of
degrees, and require a scale of 10 to convert them to degrees expected by
Home Assistant. The scale can also be the other way, for a fan with speeds
1, 2 and 3 as DP values, this can be converted to a percentage with a scale
of 0.03.
###invert
Optional, default=False.
This can be used in an integer dp mapping to invert the range. For example,
some cover devices have an opposite idea of which end of the percentage scale open
and closed are from what Home Assistant assumes. To use this mapping option, a range
must also be specified for the dp.
step
Optional, default=1.
This can be used in an integer dp mapping to make values jump by a specific
step. It can also be set in a conditions block so that the steps change only
under certain conditions. An example is where a value has a range of 0-100, but
only allows settings that are divisible by 10, so a step of 10 would be set.
icon
Optional.
This can be used to override the icon. Most useful with a dps_val which
indicates a change from normal operating mode, such as "fan-only",
"defrosting", "tank-full" or some error state.
icon_priority
Optional. Default 10. Lower numbers mean higher priorities.
When a number of rules on different attributes define icon changes, you
may need to control which have priority over the others. For example,
if the device is off, probably it is more important to indicate that than
whether it is in fan-only or heat mode. So in the off/on DP, you might
give a priority of 1 to the off icon, 3 to the on icon, and in the mode DP
you could give a priority of 2 to the fan icon, to make it override the
normal on icon, but not the off icon.
If you don't specify any priorities, the icons will all get the same priority,
so if any overlap exists in the rules, it won't always be predictable which
icon will be displayed.
value_redirect
Optional.
When value_redirect is set, the value of the attribute and any attempt to
set it will be redirected to the named attribute instead of the current one.
An example of how this can be useful is where a Tuya heater has a dp for the
target temperature in normal mode, and a different dp for the target
temperature is "eco" mode. Depending on the preset_mode, you need to use
one or the other. But Home Assistant just has one temperature attribute for
setting target temperature, so the mapping needs to be done before passing to
Home Assistant.
value_mirror
Optional.
When value_mirror is set, the value of the attribute will be redirected to
the current value of the named attribute. Unlike value_redirect, this does
not redirect attempts to set the dp to the redirected dp, but when used in
a map, this can make the mapping dynamic.
An example of how this can be useful is where a thermostat can be configured to control either a heating or cooling device, but it is not expected to change this setting during operation. Once set up, the hvac_mode dp can have a mapping that mirrors the value of the configuration dp.
invalid
Optional, default false.
Invalid set to true allows an attribute to temporarily be set read-only in
some conditions. Rather than passing requests to set the attribute through
to the Tuya protocol, attempts to set it will throw an error while it meets
the conditions to be invalid. It does not make sense to set this at mapping
level, as it would cause a situation where you can set a value then not be
able to unset it. Instead, this should be used with conditions, below, to
make the behaviour dependent on another DP, such as disabling fan speed
control when the preset is in sleep mode (since sleep mode should force low).
default
Optional, default false.
Default set to true allows an attribute to be set as the default value. This is used by some entities when an argument is not provided to a service call but the attribute is required to be set to function correctly. An example is the siren entity which uses the tone attribute to turn on and off the siren, but when turn_on is called without any argument, it needs to pick a defaulttone to use to turn on the siren.
constraint
Optional, always paired with conditions.
If a rule depends on an attribute other than the current one, then constraint
can be used to specify the element that conditions applies to.
conditions
Optional, always paired with constraint.
Conditions defines a list of rules that are applied based on the constraint
attribute. The contents are the same as Mapping Rules, but dps_val applies
to the attribute specified by constraint. All others act on the current
attribute as they would in the mapping. Although conditions are specified
within a mapping, they can also contain a mapping of their own to override
that mapping. These nested mappings are limited to simple dps_val to value
substitutions, as more complex rules would quickly become too complex to
manage.
Entity types
Entities have specific mappings of dp names to functions. Any unrecognized dp name is added to the entity as a read-only extra attribute, so can be observed and queried from HA, but if you need to be able to change it, you should split it into its own entity of an appropriate type (number, select, switch for example).
If the type of dp does not match the expected type, a mapping should be provided to convert. Note that "on" and "off" require quotes in yaml, otherwise it they are interpretted as true/false.
Many entity types support a class attribute which may change the UI behaviour, icons etc. See the HA documentation for the entity type to see what is valid (these may expand over time)
binary_sensor
- sensor (required, boolean) the dp to attach to the sensor.
climate
- aux_heat (optional, boolean) a dp to control the aux heat switch if the device has one.
- current_temperature (optional, number) a dp that reports the current temperature.
- current_humidity (optional, number) a dp that reports the current humidity (%).
- fan_mode (optional, mapping of strings) a dp to control the fan mode if available.
Any value is allowed, but HA has some standard modes:
"on", "off", auto, low, medium, high, top, middle, focus, diffuse - humidity (optional, number) a dp to control the target humidity if available. (%)
- hvac_mode (optional, mapping of strings) a dp to control the mode of the device.
Possible values are:
"off", cool, heat, heat_cool, auto, dry, fan_only - hvac_action (optional, string) a dp thar reports the current action of the device.
Possible values are:
"off", idle, cooling, heating, drying, fan - preset_mode (optional, mapping of strings) a dp to control preset modes of the device.
Any value is allowed, but HA has some standard presets:
none, eco, away, boost, comfort, home, sleep, activity - swing_mode (optional, mapping of strings) a dp to control swing modes of the device.
Possible values are:
"off", vertical, horizontal - temperature (optional, number) a dp to set the target temperature of the device. A unit may be specified as part of the attribute if a temperature_unit dp is not available, if not the default unit configured in HA will be used.
- target_temp_high (optional, number) a dp to set the upper temperature range of the device.
This dp should be paired with
target_temp_low, and is mutually exclusive withtemperature - target_temp_low (optional, number) a dp to set the lower temperature range of the device.
- temperature_unit (optional, string) a dp that specifies the unit the device is configured for. Values should be mapped to "C" or "F" (case sensitive) - often the device will use a boolean or lower case for this
- min_temperature (optional, number) a dp that specifies the minimum temperature that can be set. Some devices provide this, otherwise a fixed range on the temperature dp can be used.
- max_temperature (optional, number) a dp that specifies the maximum temperature that can be set.
cover
Either position or open should be specified.
- position (optional, number 0-100): a dp to control the percentage that the cover is open. 0 means completely close, 100 means completely open.
- control (optional, mapping of strings): a dp to control the cover. Mainly useful if position cannot be used.
Valid values are
open, close, stop - action (optional, string): a dp that reports the current state of the cover.
Special values are
opening, closing - open (optional, boolean): a dp that reports if the cover is open. Only used if position is not available.
fan
- switch (optional, boolean): a dp to control the power state of the fan
- preset_mode (optional, mapping of strings): a dp to control different modes of the fan.
Values
"off", low, medium, highused to be handled specially by HA as deprecated speed aliases. If these are the only "presets", consider mapping them as speed values instead, as voice assistants will respond to phrases like "turn the fan up/down" for speed. - speed (optional, number 0-100): a dp to control the speed of the fan (%). scale and step can be used to convert smaller ranges to percentages, or a mapping for discrete values.
- oscillate (optional, boolean): a dp to control whether the fan will oscillate or not.
- direction (optional, string): a dp to control the spin direction of the fan.
Valid values are
forward, reverse.
humidifier
Humidifer can also cover dehumidifiers (use class to specify which).
- switch (optional, boolean): a dp to control the power state of the fan
- mode (optional, mapping of strings): a dp to control preset modes of the device
- humidity (optional, number): a dp to control the target humidity of the device
light
- switch (optional, boolean): a dp to control the on/off state of the light
- brightness (optional, number 0-255): a dp to control the dimmer if available.
- color_temp (optional, number): a dp to control the color temperature if available. will be mapped so the minimum corresponds to 153 mireds (6500K), and max to 500 (2000K).
- rgbhsv (optional, hex): a dp to control the color of the light, using encoded RGB and HSV values. The
formatfield names recognized for decoding this field arer,g,b,h,s,v. - color_mode (optional, mapping of strings): a dp to control which mode to use if the light supports multiple modes.
Special values:
white, color_temp, rgbw, hs, xy, rgb, rgbww, others will be treated as effects, Note: only white, color_temp and rgbw are currently supported, others listed above are reserved and may be implemented in future when the need arises. - effect (optional, mapping of strings): a dp to control effects / presets supported by the light. If the light mixes in color modes in the same dp, color_mode should be used instead.
lock
- lock (optional, boolean): a dp to control the lock state: true = locked, false = unlocked
- unlock_fingerprint (optional, integer): a dp to identify the fingerprint used to unlock the lock.
- unlock_password (optional, integer): a dp to identify the password used to unlock the lock.
- unlock_temp_pwd (optional, integer): a dp to identify the temporary password used to unlock the lock.
- unlock_dynamic_pwd (optional, integer): a dp to identify the dynamic password used to unlock the lock.
- unlock_card (optional, integer): a dp to identify the card used to unlock the lock.
- unlock_app (optional, integer): a dp to identify the app used to unlock the lock.
- request_unlock (optional, integer): a dp to signal that a request has been made to unlock, the value should indicate the time remaining for approval.
- approve_unlock (optional, boolean): a dp to unlock the lock in response to a request.
- jammed (optional, boolean): a dp to signal that the lock is jammed.
number
- value (required, number): a dp to control the number that is set.
- unit (optional, string): a dp that reports the units returned by the number. This may be useful for devices that switch between C and F, otherwise a fixed unit attribute on the value dp can be used.
- minimum (optional, number): a dp that reports the minimum the number can be set to. This may be used as an alternative to a range setting on the value dp if the range is dynamic
- maximum (optional, number): a dp that reports the maximum the number can be set to. This may be used as an alternative to a range setting on the value dp if the range is dynamic
select
- option (required, mapping of strings): a dp to control the option that is selected.
sensor
- sensor (required, number or string): a dp that returns the current value of the sensor.
- unit (optional, string): a dp that returns the unit returned by the sensor. This may be useful for devices that switch between C and F, otherwise a fixed unit attribute on the sensor dp can be used.
switch
- switch (required, boolean): a dp to control the switch state.
- current_power_w (optional, number): a dp that returns the current power consumption in watts. This is a legacy attribute, for the HA Energy dashboard it is advisable to also provide a sensor entity linked to the same dp as well.
vacuum
- status (required, mapping of strings): a dp to report and control the status of the vacuum.
- command (optional, mapping of strings): a dp to control the statuss of the vacuum. If supplied, the status dp is only used to report the state.
Special values:
return_to_base, clean_spot, others are sent as general commands - locate (optional, boolean): a dp to trigger a locator beep on the vacuum.
- power (optional, boolean): a dp to switch full system power on and off
- activate (optional, boolean): a dp to start and pause the vacuum
- battery (optional, number 0-100): a dp that reports the current battery level (%)
- direction_control (optional, mapping of strings): a dp that is used for directional commands These are additional commands that are not part of status. They can be sent as general commands from HA.
- error (optional, bitfield): a dp that reports error status. As this is mapped to a single "fault" state, you could consider separate binary_sensors to report on individual errors
siren
- tone (required, mapping of strings): a dp to report and control the siren tone. As this is used to turn on and off the siren, it is required. If this does not fit your siren, the underlying implementation will need to be modified. The value "off" will be used for turning off the siren, and will be filtered from the list of available tones.
- volume (optional, float in range 0.0-1.0): a dp to control the volume of the siren (probably needs a scale and step applied, since Tuya devices will probably use an integer, or strings with fixed values).
- duration (optional, integer): a dp to control how long the siren will sound for.